Decorative corner 142501154 XCMG truck crane spare parts

Short Description:

Some of our crane accessories available
LD wheel, wheel set, reel set, hook set, pulley set, coupling, wire rope, cable pulley, running motor, brake, reducer, cable reel, overload limiter, standard parts.
Inverter, remote control, resistor, control panel, explosion-proof motor, explosion-proof electrical appliance, control cable, overload limiter, protection cabinet, explosion-proof limiter, limit switch, rail clamp, current collector.

Send email to us

Product Detail

Product Tags

description

Part No: 142501154
Part name: Decorative corner
Compatible equipment model: 25t truck crane and other xcmg truck cranes
Part brand: XCMG

Due to too many types of spare parts, we cannot display them all on the website. Please feel free to contact us for specific information. The following are some other related product part numbers：

800933821 STR foot relay valve
800936412 TA-125 air filter
803300590 GB/T9877-2008 Skeleton Oil Seal FB115×140×12
803613324 Fuse 30A (chip)
803700057 SG253 Flashing relay
805000678 GB/T5782-2000 Bolt M24×120(10.9)
805010065 GB/T5785-2000 Bolt M12×1.5×28
805048254 GB/T5782-2000 Bolt M24×145 10.9(Dacromet)
805100366 GB/T818-2000 Screw M10×20
805100505 GB/T70.1-2008 Screw M10×35 10.9
805203877 GB/T6172.1-2000 Nut M20(10)
805238936 GB/T6172.1-2000 Nut M12 (Dacromet)
805301390 GB/T849-1988 Washer 30
805301394 GB/T850-1988 Washer 30
805801448 JB3616.1-1984 Double steel wire hoop 65-70
819906720 BHR204-89-600 Lower parallel idler
840344115 (replaced by 840344109) positive 90° offset knife (large)
840344118 (replaced by 840344111) positive 45° offset knife (large)
860138276 3901177 Air valve lock block 6CTA8.3-C260-Ⅱ (spare part)
276100616 LQC80B.5.1-9 paddle arm (two)
380901050 GR215Ⅹ.14.6-1 rubber tube
800307349 CW12E12004022 reducer
800933822 QZ50A manual control valve (ZL)
803074425 XGHP-02 Hand pump
803190327 XGHZJT-1 rotary joint
803190381 CF1840 safety filter element
803677787 KNG3-101 Two-position non-reset twist switch
805000407 GB/T5782-2000 Bolt M16×140
805203871 GB/T6181-1986 Nut M36×2
276403298 LQC160C.2.2.3 large feeder
276403465 LQC160C.2.2.2-3 Support seat two
276403466 LQC160C.2.2.2-2 Support seat one
276611084 XAP320.5.1.1-3A Blade
276921308 XAP160.5.1.1.2.1-2Ⅱ Blade
380500427 GR165Ⅲ.20.1-2 Pipe clamp
380900994 GR215A.17-2 gland
380901058 GR215Ⅹ.17-20 Washer
380901170 GR215C.18-5 Rubber pad
380901295 NBS504 lock
381601099 PY180G.12.2-14 drive wheel ZBJ
384200540 RH200.12.1.1.2 wear plate
800752690 Drain valve CA10

Some common crane accessories product introduction
1. Steel wire rope.
Check that the wire rope specification, model and slip drum match are in accordance with the design requirements. Whether the fixed installation of wire ropes, such as wire rope fixed end clips, rope clip blocks, etc., meets the requirements. Whether the wire rope is worn, broken, kinked, flattened, bent, broken, and corroded.
2. Crane hook
Check whether the crane hook and anti-dropping equipment meet the requirements, whether the hook has cracks, peeling cracks and other defects; whether the hook section is worn, the increase in opening, torsional deformation, and whether it exceeds the standard; the hook neck and surface fatigue deformation and cracks and related Wear of pin bushings.
3. Coupling.
Whether the coupling parts are damaged, the connection is loose, and the running impact phenomenon. Whether the wear of the coupling, pin shaft, shaft pin hole and buffer rubber ring exceeds the standard. Whether the coupling is concentric with the two parts being connected.
4. Reel.
Whether the drum body and drum edge have fatigue cracks, damage, etc.; whether the wear of the rope groove and drum wall exceeds the standard; whether the height of the drum rim matches the number of layers of wire rope winding; whether the working conditions of the rope guide and rope arrangement meet the requirements Require;
5. Braking device.
The setting of the brake, whether the type of the brake meets the design requirements, whether the tie rod and spring of the brake have any defects such as fatigue deformation and cracks; whether the pin shaft, spindle, brake wheel, and brake friction plate are worn beyond the standard, and whether the hydraulic brake leaks oil ; Whether the braking clearance adjustment and braking capacity can meet the requirements.
6. Pulley.
Whether the pulley is equipped with an anti-dropping rope groove device; whether the pulley rope groove and wheel flange have cracks, broken edges, excessive wear, etc., and whether the pulley rotates flexibly.

Welcome to consult us or search on our site for more spare parts！

advantage

1. We supply both original and aftermarket products for you
2. From the manufacturer to the customer directly, saving your cost
3. Stable stock for normal parts
4. In Time Delivery Time, with competitive shipping cost
5. Professional and on time after service